- Description
Details
The C4 has a wider dispersion than the larger models. It contains a proprietary Tru-Phase™ waveguide that produces a consistently wide conical polar response up to 16 kHz. The C4 features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities.
Each model is delivered as a pair of loudspeakers, fully assembled, and including everything needed for standard installations.
- Features
Features
- High intelligibility with exceptional uniform coverage
- Consistent, wide dispersion up to 16 kHz
- True coaxial loudspeakers with HF compression drivers
- Tru-Phase high-frequency waveguide
- Spring loaded Drop-Stop installation assistant tabs
- support the back can on the included rails simplify installation
- Uniquely designed tile bridge support rails prevent ceiling tile sagging
- External loop-through Euroblock connectors
- Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
- Face-mounted adjustable tap position selector switch
- Selectable 8 ohm or 70V/100V operation
- Specification
Loudspeaker Type Two-way, full-range, coaxial ceiling loudspeaker, 8 ohm or 70V/100V operation Operating Range 75 Hz - 13.5 kHz (-10 dB) Frequency Response 125 Hz - 12.5 kHz (-3 dB) Max Input Ratings (8 ohm) 60W continuous, 150W program 21.9 volts RMS, 43.8 volts momentary peak Transformer Taps 70V 8W, 4W, 2W, 1W, and 8 ohm selectable 100V 16W, 8W, 4W, 2W, and 8 ohm selectable 10% Full Power 500 Hz 2nd Harmonic : 1.03%, 3rd Harmonic : 0.21% 2 kHz 2nd Harmonic : 0.69%, 3rd Harmonic : 0.25% 8 kHz 2nd Harmonic : 1.21%, 3rd Harmonic : 0.15% 1% Full Power 500 Hz 2nd Harmonic : 0.43%, 3rd Harmonic : 0.19% 2 kHz 2nd Harmonic : 0.82%, 3rd Harmonic : 0.29% 8 kHz 2nd Harmonic : 0.54%, 3rd Harmonic : 0.07% Sensitivity (1W/1m) 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands), 90 dB SPL (250 Hz to 4 kHz speech range) Maximum Output 8 Ohm 109 dB SPL / 115 dB SPL (peak) 70V 100 dB SPL / 106 dB SPL (peak) 100V 103 dB SPL / 109 dB SPL (peak) Nominal Impedance 8 ohms Minimum Impedance 7 ohms @ 10 kHz Nominal Coverage 130º conical (1 kHz to 6 kHz ±60°), 140° conical (500 Hz to 6 kHz ±65°) Axial Q / DI 4.0 / 6.0, 500 Hz to 6 kHz Crossover Frequency 2 kHz Recommended Signal Processing 110 Hz, at 24 dB per octave high pass filter Drivers LF 1 x 4.5-inch cone HF 1 x ¾-inch exit compression driver Driver Protection Self-resetting solid state circuit breaker Input Connection 4-pole Euroblock connector with two pair of non-interrupt parallel connections Controls Front-face wattage / low impedance selector switch Enclosure Corrosion-resistant zinc plated steel Finish White Mounting/Rigging Provisions 2 ABS mounting clamps with 1.75-inch grip range Grille Powder coated steel with safety line, white finish, paintable Baffle Reflex loaded UL 94V-0 rated ABS Safety Features 2 x safety hang points Required Accessories Electronic high pass filter Supplied Accessories Tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver Physical Cutout Diameter 7.36" (187.0 mm) Dimensions (Dia x D) 8.31" (211.07 mm) x 5.50" (139.7 mm) Weight 6.4 lbs (2.9 kg) - Documents
Documents
- Reviews
Write Your Own Review