- Description
Details
The C6 6.5 inch Two Way In-Ceiling Loudspeaker has a more focused dispersion and a greater low frequency extension than the smaller C4. It contains a proprietary Tru-Phase waveguide that produces a consistently wide conical polar response up to 16 kHz. The C6 features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities.
- Features
Features
- High intelligibility with exceptional uniform coverage
- Consistent, wide dispersion up to 16 kHz
- True coaxial loudspeakers with HF compression drivers
- Tru-Phase high-frequency waveguide
- Spring loaded Drop-Stop installation assistant tabs support the back can on the included rails simplify installation
- Uniquely designed tile bridge support rails prevent ceiling tile sagging
- External loop-through Euroblock connectors
- Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
- Face-mounted adjustable tap position selector switch
- Selectable 8 ohm or 70V/100V operation
- Specification
Operating Range 70 Hz - 13.5 kHz (-10 dB) Frequency Response 115 Hz - 12.5 kHz (-3 dB) Max Input Ratings (8 ohm) 60W continuous, 150W program
21.9 volts RMS, 43.8 volts momentary peakTransformer Taps 70V: 30W, 15W, 7.5W, 3.75W, and 8 ohm selectable
100V: 30W, 15W, 7.5W, and 8 ohm selectableDistortion 10% Full Power 500 Hz 2nd Harmonic : 0.33%, 3rd Harmonic : 0.55% 2 kHz 2nd Harmonic : 1.11%, 3rd Harmonic : 0.80% 8 kHz 2nd Harmonic : 2.49%, 3rd Harmonic : 0.21% Distortion 1% Full Power 500 Hz 2nd Harmonic : 0.25%, 3rd Harmonic : 0.06% 2 kHz 2nd Harmonic : 0.67%, 3rd Harmonic : 0.23% 8 kHz 2nd Harmonic : 0.30%, 3rd Harmonic : 0.06% Sensitivity (1W/1m) 91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands)
91 dB SPL (250 Hz to 4 kHz speech range)Maximum Output 8Ω: 109 dB SPL / 115 dB SPL (peak)
70V: 106 dB SPL / 112 dB SPL (peak)
100V: 106 dB SPL / 112 dB SPL (peak)Nominal Impedance 8 ohms Minimum Impedance 7 ohms @ 10 kHz Nominal Coverage 120º conical (1 kHz to 6 kHz ±65°), 120° conical (500 Hz to 6 kHz ±65°) Axial Q / DI 4.9/6.9, 500 Hz to 6 kHz Crossover Frequency 2 kHz Recommended Signal Processing 100 Hz, at 24 dB per octave high pass filter Drivers LF 1 x 6.5" cone, HF 1 x 3/4" exit compression driver Driver Protection Self-resetting solid state circuit breaker Input Connection 4-pole Euroblock connector with two pair of non-interrupt parallel connections Controls Front-face wattage / low impedance selector switch Enclosure Corrosion-resistant zinc plated steel Finish White or black Mounting/Rigging Provisions 2 ABS mounting clamps with 1.75" grip range Grille Powder coated steel with safety line, white or black finish, paintable Baffle Reflex loaded UL 94V-0 rated ABS Safety Features 2 x safety hang points Required Accessories Electronic high pass filter Supplied Accessories Tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver Physical Cutout Diameter 8.86" (225 mm) Dimensions (Dia x D) 9.80" (248.9 mm) x 6.49" (164.8 mm) Net Weight 7.1 lbs (3.2 kg) - Documents
Documents
- Reviews
Write Your Own Review