- Description
Details
The CMS 603DC PI is a full bandwidth 320-Watt high sensitivity loudspeaker that utilizes our third generation Ceiling Monitor System technology (CMS 3.0). Thanks to an all-new proprietary 6" Dual Concentric point source driver with Omnimagnet technology on a Torus Ogive Waveguide, the UL certified CMS 603DC PI delivers wide and consistent broadband directivity with enhanced intelligibility – plus highly accurate and linear response.
Optimized for Installation
Specifically designed with a self-aligning 4-way clamp system for fast, simple and cost-effective installation, CMS 603DC PI also features extra clamp extension to accommodate thicker ceiling panels, and a locking design that prevents over-tightening. A low-insertion loss 60 W transformer with convenient front panel tap switching, paintable powder coated steel mesh grille with dust protection, two tile support rails, and one C-ring are all included. An Arco™ style grille, which conceals the entire unit for aesthetic purposes, a back can, and plaster (mud) ring are available separately.
LAB GRUPPEN Ready
The CMS 603DC PI is finished in semi-matte white and optimised for use with LAB GRUPPEN LUCIA amplifiers, which accommodate up to 8 CMS Series loudspeakers per channel.
- Features
Features
- Full range ceiling loudspeaker for installation applications
- 80 Watts continuous, 320 Watts peak power
- Next generation 6" Dual Concentric driver featuring Omnimagnet technology
- Torus Ogive waveguide for improved high-frequency response and directivity
- Pre-install version supplied without back can (available separately)
- UL 1480 certified for general signaling systems
- UL 2043 certified for air-handling spaces
- Multiple transformer taps for 70 V and 100 V line systems or 16 Ohm direct input
- Low insertion loss 60 W line transformer with easily accessible tapping switch
- Optimised for LAB GRUPPEN low impedance LUCIA amplifiers with up to 8 CMS series loudspeakers per channel
- Semi-matte white finish fits unobtrusively in any environment
- Powder coated UV resistant perforated steel mesh grille with dust protection
- Removable magnetic grille for custom painting
- Optional ARCO designer grilles available for minimal architectural impact
- Self-aligning 4 way clamp mounting system
- Mounting C-ring and ceiling tile rails included
- 10-Year Warranty Program
- Designed and engineered in the U.K.
- Specification
Performance Frequency Response (-3 dB) 75 Hz - 30 kHz Frequency Range (-10 dB) 50 Hz - 30 kHz System Sensitivity (1 W @ 1 m) 91 dB (1 W = 4 V for 16 Ohms) Nominal Coverage Angle 90 degrees conical Power Handling Average: 80 W
Program: 160 W
Peak: 320 WRecommended Amplifier Power 160 W @ 16 Ohms Nominal Impedance (Lo, Z) 16 Ohms Rated Maximum SPL Average: 110 dB
Peak: 116 dBTransformer Taps (via Front Rotary Switch) 70 V: 60 W (83 Ohms) / 30 W (165 Ohms) / 15 W (330 Ohms) / 7.5 W (660 Ohms) / OFF & low impedance operation
100 V: 60 W (165 Ohms) / 30 W (330 Ohms) / 15 W (660 Ohms) / OFF & low impedance operationTransducers Dual Concentric Point Source Driver 1 x 6.5" (165 mm) Dual Concentric driver, using Omnimagnet technology High Frequency 1.00" (25 mm) PEI dome Low Frequency 1.75" (44 mm) voice coil, treated multi fiber paper pulp cone Physical Enclosure Back Can: Zinc plated steel
Baffle: UL 94 V-0 rated ABS
Grille: Steel, with weather resistant coatingSafety Features Safety ring located at rear of enclosure for load bearing safety bond Clamping Design Security toggle clamp. Min / Max clamping range 0.37" ( 9.5 mm ) / 2.36" ( 60 mm )
Recommended clamp torque: 1.5 NmBackcan Options Separate backcan for pre-installation Cable Entry Options Cable clamp & squeeze connector for conduit up to 22 mm Conduit Knockouts on PI Backcan 3 Sets of horizontal positions: 0.75" / 0.87" / 1.10" ( 19 / 22 / 28 mm ) Connectors Removable locking connector with screw terminals with "loop through" facility Compliance UL-1480, UL-2043, CE Dimensions Bezel Diameter 10.79" (274.0 mm) Front of Ceiling to Rear of Backcan 10.07" (255.8 mm) Front of Ceiling to Top of Safety Loop 10.76" (273.3 mm) Hole Cutout Diameter (All Models) 9.96" (253 mm) Net Weight 16.1 lbs (7.3 kg) Shipping Weight 25.4 lbs (11.52 kg) - Documents
- In The Box
In The Box
- (2) CMS 603DC PI Speakers
- (2) C Rings
- (2) Tile Bridges
- (2) Paint Mask
- (2) Cutout Template
- (2) Grilles
- Reviews
Write Your Own Review