- Description
Details
The C 28:4 is one of two mid-power, four-channel amplifiers in the C Series family. Attractively packaged in a 2U chassis, it provides 4 × 700W output into 4 ohm loads.
C Series amplifiers are uniquely capable of adapting to a wide variety of demanding load conditions. Each channel has an individually configurable Voltage Peak Limiter (VPL™), which allows the output to be optimized for any loudspeaker load – whether a single large subwoofer or a series of small 100/70V loudspeakers. VPL works in combination with adjustable input gain to achieve maximum headroom regardless of input levels or output impedances.
Every C Series is ready for the NomadLink® network right out of the box. With NomadLink, key amplifier parameters are displayed via DeviceControl software, and remote control of channel mutes and power on/off is under network control.- Features
Features
- Unprecedented power density – Total output of 2800W (4 ohms) in a 2U cabinet
- Four channels – All channels bridgeable for 2- or 3-channel configurations
- Lo-Z or Hi-Z (70V / 100V) – Selectable per channel, normal or bridged
- Patented Class TD® amplifier topology
- Voltage Peak Limiter (VPL) – Configurable per channel to optimize each output for connected loads
- Phoenix-type input connectors
- Screw terminal output connectors
- Comprehensive protection and warning – Excessive output current, DC, high temperature, very high frequency (VHF), short circuit, open load, mains fuse protection, and soft start
- Efficient and uniform Intercooler® cooling
- NomadLink® network ready
- Specification
General Number of Channels 4 Peak Total Output all Channels Driven 2800W Peak Output Voltage per Channel 141V Max. Output Current per Channel 12 Arms Max. Output Power 16 ohms Per ch. (all ch.’s driven) : 600W; Bridged per ch. :1400W 8 ohms Per ch. (all ch.’s driven) : 700W; Bridged per ch. :1200W 4 ohms Per ch. (all ch.’s driven) : 700W; Bridged per ch. :600W 2 ohms Per ch. (all ch.’s driven) : 300W Hi-Z Per ch: 700W (70V rms / 100V peak); Bridged per ch.:1400W (140V rms / 200V peak) Performance with Gain: 35 dB and VPL: 100V THD 20 Hz - 20 kHz for 1W <0.1% THD at 1 kHz and 1 dB Below Clipping <0.05% Signal To Noise Ratio >112 dBA Channel Separation (Crosstalk) at 1 kHz >70 dB Frequency Response (1W into 8Ω) +0/-3 dB 6.8 Hz - 34.2 kHz Input Impedance 20k Ohm Input Common Mode Rejection, CMR 50 dB Output Impedance @ 100 Hz 30m Ohm Voltage Peak Limiter (VPL), Max. Peak Output VPL, Selectable per Ch. 141, 118, 100, 85, 71, 59, 50, 42V VPL, when Bridged 282, 236, 200, 170, 142, 118, 100, 84V Voltage Peak Limiter Mode (per Ch.) Hard / Soft Gain and Level Amplifier Gain Selectable (all Channels) – Rear-Panel Switches 23, 26, 29, 32, 35, 38, 41, 44 dB Default Gain 35 dB Connectors and Switches Input Connectors (per Ch.) 3-pin Phoenix, electronically balanced Output Connectors (per Ch.) Barrier strip 2-pole screw terminals Output Bridge Mode A+B and/or C+D, inputs A and C are input source NomadLink® Network On board, 2 x RJ45 connectors Intelligent Fans (on/off) Yes, depending on presence of output signal Power on/off and Remote Enable on/off Individual switches on front-panel Cooling Two fans, front-to-rear airflow, temperature controlled speed Power Operating Voltage, 230V / 115V Nominal 130 - 265 / 65 - 135V Minimum Power-Up Voltage, 230V / 115V 171V / 85V Power Average Limiter (PAL) Yes Soft Start / Inrush Current Draw Yes / max. 5 A Mains Connector 230V CE: 16 A, CEE7; 115V ETL: 20 A / NEMA 5-20P Dimensions (H x W x D) 3.46" (88 mm) x 19" (483 mm) x 13.5" (343 mm) Weight 26.4 lbs (12 kg) - Documents
Documents
- Reviews
Write Your Own Review