Commercial Sound Equipment

The Ashly KLR 3200 high-performance power amplifier is optimized to provide reliable audio performance with sonic perfection. Covering a power range from 1000 to 2500 Watts per channel at 2 ohms the KLR 3200 is perfectly suited for a wide range of sound reinforcement.

The Ashly Pema 4125 DSP processor features a new sleek look, 4-channel at 125 watts per channel at 4Ω. The Pema is a matrix mixer with 8-in x 8-out, where any input can be assigned to any output or outputs.

The Ashly Pema 4250 DSP Processor is a Protea-Equipped Media Amplifier—either 4-channel at 250 Watts per channel. Pema is a matrix mixer—all Pema models have a full 8-in x 8-out matrix mixer, where any input can be assigned to any output or outputs. Pema is a digital signal processor.

The Ashly Pema 8250 DSP Processor is a Protea-Equipped Media Amplifier. It features 8-channesl at 250 Watts per channel. Pema is a matrix mixer—all Pema models have a full 8-in x 8-out matrix mixer, where any input can be assigned to any output or outputs.

The Ashly WR-1 is an assignable, dual potentiometer remote volume control for the controlled product. Each volume control is connected to a euroblock jack terminal on the WR-1 circuit board, which in turn must be wired to the 24.24M back panel euroblock connector labeled "0 - 5 Volt Remote Level Control".

The Ashly WR-2 Multi-Function Wall Network Remote Volume Control allows selection of one of four presets via interlocking pushbutton switches. Each pushbutton switch connects to a euroblock on the rear of the controlled product.

The Ashly WR-1.5 volume control fits in standard wall boxes and used low gauge wire for hook-up. It has a single potentiometer for remote level control, plus a 4-position rotary switch for preset recall. The remote level control uses DC voltage provided by the host unit to attenuate one channel of that unit.

Control your system from any location with the Ashly WR-5 Programmable Multi-Function Decora Wall Remote Control. This device fits in standard wall boxes and uses low gauge wire for hook-up. WR-5 is a programmable remote button controller for Ashly amps and processors that have a serial data connector.

Control your system from any location with this Network Enabled remote control. The neWR-5 is a programmable remote button controller for Ashly Network Enabled amps and processors.

Control your system from any location with this wall-mountable RRW-8C wall-mountable programmable remote fader controller for Ashly amps and processors that have DSP and a serial data connector.

The Ashly SRA-2075 power amplifier is an advanced, efficient amplifier that is perfect for installations with modest power requirements. Housed in a compact single rack space chassis and weighing only 10 lbs, and designed to drive 4 or 8 ohm loads.

The Ashly FA-125.2 is designed for easy and flexible placement, to go where other amps cannot: Under conference tables, behind displays, inside kiosks...anywhere high-quality reliable power is needed, but space is limited. The FA Series is that neat audio magic trick that gives your project the performance you need...without the bulk, heat, and power-consumption you don't.

The Ashly Audio SRA-2150 1U power amplifier is an advanced, efficient amplifier that is perfect for installations with modest power requirements. Housed in a compact single rack space chassis and weighing only 10 lbs, and designed to drive 4 or 8 ohm loads. With remote power turn-on/off and adjustable turn-on delay up to eight seconds.

The Ashly FA-125.4 is designed for easy and flexible placement, to go where other amps cannot: Under conference tables, behind displays, inside kiosks...anywhere high-quality reliable power is needed, but space is limited. The FA Series is that neat audio magic trick that gives your project the performance you need...without the bulk, heat, and power-consumption you don't.

The Ashly nX 752 Multi-Mode Power Amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces and convention centers.

The TRA-2075 power amplifier is an advanced, efficient 2-channel amplifier featuring 75W at 4 ohm. Perfect for Low Impedance, 70V or 100V installations with modest power requirements, they also feature a switch-mode power supply with Class-D circuitry, providing an extremely power-efficient solution.

Specifying the right power amp is often easier than finding it. The SRA-4075 makes it a snap to get exactly what you need. SRAs are advanced, efficient amplifiers perfect for installations with modest power requirements. Housed in a compact single rack space chassis, and weighing only 10lbs, they're designed to drive 4 or 8 Ohm loads.

The Ashly FA-250.4 is designed for easy and flexible placement, to go where other amps cannot: Under conference tables, behind displays, inside kiosks...anywhere high-quality reliable power is needed, but space is limited. The FA Series is that neat audio magic trick that gives your project the performance you need...without the bulk, heat, and power-consumption you don't.

The Ashly nX 1502 Multi-Mode Power Amplifier is designed to meet the most demanding live sound and fixed installation sound systems in stadiums, arenas, performance venues, worship spaces and convention centers.

The TRA-2150 power amplifier is an advanced, efficient 2-channel amplifier featuring 150W at 4 ohm Perfect for Low Impedance, 25V, 70V or 100V installations with modest power requirements, they also feature a switch-mode power supply with Class-D circuitry, providing an extremely power-efficient solution.