- Description
Details
The Community CS6 6.5 inch Two Way Surface Mount Loudspeaker incorporates the same full-range loudspeaker (as the C6) in a black or white paintable ABS surface mount enclosure. It also has a more focused dispersion than the smaller CS4. It contains a proprietary Tru-Phase™ waveguide that produces a consistently wide conical polar response up to 16 kHz. The CS6 features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products.
Easily outperforming loudspeakers of a larger size format, the CS6 provides high power handling, high sensitivity and realistic sound reproduction. This loudspeaker is equipped with a built-in autoformer, allowing large numbers of distributed loudspeakers to be powered from a 70V or 100V amplifier output. A convenient front-accessible power tap switch is hidden behind a rotatable logo. Installation is simple and flexible using the included multi-angle pan-tilt bracket which allows low profile mounting and precise positioning of the enclosure in either horizontal or vertical orientation.
Thanks to the internally reinforced, black or white paintable ABS enclosures, zinc-rich epoxy dual-layer powder-coated grilles and brackets, weather-treated drivers, and the included IP56 sealed wiring cover, all standard surface mount models are equally suited for indoor or outdoor direct exposure applications.
- Features
Features
- Clean and simple architectural design
- Same components and voicing as the Commercial Design ceiling loudspeaker family
- High efficiency, high output, high intelligibility, low distortion
- Paintable enclosure constructed of high-impact ABS plastic to reduce resonances
- Front-accessible power tap switch for selectable 8 ohm or 70V/100V operation
- Low profile pan-tilt mounting yoke included
- Horizontal or vertical mounting orientation
- Weather-resistant construction with treated drivers, two-layer powder coated grilles and protected wiring ingress
- Available in standard black or white finishes
- Specification
Operating Range 65 Hz - 13.5 kHz (-10 dB) Frequency Response 90 Hz - 12.5 kHz (-3 dB) Max Input Ratings (8 ohm) 60W continuous, 150W program 22 volts RMS, 43.8 volts momentary peak Transformer Taps—70V; 100V 30W, 15W, 7.5W, 3.75W and 8 ohm selectable; 30W, 15W, 7.5W, and 8 ohm selectable Sensitivity (1W/1m) 90 dB SPL (90 Hz to 12.5 kHz 1/3 octave bands), 91 dB SPL (250 Hz to 4 kHz speech range) Maximum Output 108 dB SPL / 114 dB SPL (peak 8 ohm) Nominal Impedance 8 ohms Minimum Impedance 6.4 ohms @ 10 kHz Nominal Coverage 120º conical (+60° / -60°, 1 kHz to 6 kHz) Axial Q / DI 4.8 / 6.8, 500 Hz to 6 kHz Crossover Frequency 2 kHz Recommended SignalProcessing 70 Hz, 24 dB/Oct high pass filter Drivers LF 1 x 6.5" cone; HF 1 x 3/4" exit compression driver Driver Protection Self-resetting solid state circuit breaker Input Connection 4-pole Euroblock connector with two pair of non-interrupt parallel connections Controls Front-accessible wattage / low impedance selector switch hidden behind the rotatable logo Enclosure ABS plastic, matte finish, paintable Finish Black or white Mounting/RiggingProvisions Low profile, multi-angle, pan-tilt mounting yoke Grille Dual-layer powder coated steel, black or white finish Safety Features Built-in safety cable attachment eyebolt Environmental IP55 rated loudspeakers, IP56 rated connector cover, designed to Mil Spec 810 Required Accessories Electronic high pass filter Supplied Accessories Low profile, pan-tilt mounting yoke; flat-headscrew driver Optional Accessories M8 x 15.5mm Blind Insert for 3rd party accessory attachment Dimensions (H x W x D) 6.96" (177 mm) x 11.8" (300 mm) x 10.7" (272 mm) Weight (without bracket) 7.1 lbs (3.2 kg) Weight (with bracket) 9 lbs (4.1 kg) Shipping Weight (Pairs) 23 lbs (10.4 kg) - Reviews
Write Your Own Review