Community DP8 8" High Output High Quality 2-Way Pendant Mount Loudspeaker 150W 8 Ohm or 70V/100V - Black (Discontinued)
Usually arrives in 5-9 business days.
The Community D6 Ceiling Speaker provides high quality paging and musical performance suitable for retail environments, restaurants, resorts, and numerous other applications where the importance of sonic quality cannot be ignored.
Available in standard white or black finish, the powerful and versatile D SERIES D6 provides high-quality paging and musical performance suitable for retail environments, restaurants, resorts, and numerous other applications where the importance of sonic quality cannot be ignored. Particularly effective when supported by the D10SUB, a D6 system is capable of meeting demanding needs at a cost usually associated with much smaller loudspeakers.
Uniform voicing means that the D6 can be combined with both smaller and larger models from the Distributed Design family without compromising consistency from zone to zone. The genuine coaxial design uses separate magnets for the LF and HF drivers for reduced distortion and industry-leading sensitivity, thereby permitting 3 dB to 6 dB greater output level while requiring half the amplification power of competing products.
The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz. Community's patented Carbon Ring Cone Technology™ increases the effective cone area to further reduce distortion while reinforcing the cone for improved durability.
Exclusive Drop-Stop™ and Twist-Assist™ tabs allow single-handed placement to speed installation and reduce labor time. Drop-Stop’s spring-loaded legs support the back can on the included tile rails and nap-on C-ring, so that the installer no longer needs to hold the can against the tile while tightening the clamps. Twist-Assist performs a similar function for the baffle assembly: when the loudspeaker back cans are pre-installed into a conduit system for termination at a later date, a simple twist of the baffle into the back can brings the Twist-Assist clips together, supporting the baffle assembly while the installer fastens the screws.
The front-face wattage selector switch enables quick adjustment of 70V/100V tap levels. A variety of installation accessories are available to accommodate different ceiling materials. The D6 face-only assembly and back can are also available for separate purchase.
| Operating Range | 65 Hz - 22 kHz |
|---|---|
| Frequency Response | 80 Hz - 20 kHz (±5 dB) |
| Max Input Ratings (8 ohm) | 100W continuous, 250W program 28 volts RMS, 63 volts momentary peak |
| Transformer Taps | 60W, 30W, 15W, 7.5W and low impedance 60W, 30W, 15W |
| Sensitivity (1W/1m) | 94 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands) 92 dB SPL (250 Hz to 4 kHz speech range) |
| Maximum Output | 114 dB SPL / 120 dB SPL (peak 8 ohm) |
| Nominal Impedance | 8 ohms |
| Nominal Coverage | 115º conical (1 kHz to 6 kHz) 125º conical (500 Hz to 6 kHz) |
| Axial Q / DI | 4.7 / 6.7, 500 Hz to 6 kHz |
| Crossover Frequency | 1.2 kHz |
| Recommended Signal Processing | 65 Hz high pass filter |
| Drivers | LF 1 x 6.5" HF 1 x 1" exit compression driver |
| Driver Protection | Self-resetting solid state circuit breaker |
| Input Connection | 4-position Euroblock connector |
| Controls | Front-face wattage / low impedance selector switch |
| Enclosure | Corrosion-resistant zinc plated steel |
| Mounting/Rigging Provisions | 4 steel mounting clamps with 3-inch grip range |
| Grille | Powder coated steel with safety line, white or black finish, paintable |
| Baffle | Reflex loaded UL 94V-0 rated ABS |
| Safety Features | 4 x safety hang points |
| Safety Agency Ratings | ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90 |
| Required Accessories | Electronic high pass filter |
| Supplied Accessories | C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver |
| Optional Accessories | D6-FAR Face Adapter Ring (white) D6-CATR Can Adapter Ring / Trim Ring (white) D6-FAR-B Face Adapter Ring (black) D6-CATR-B Can Adapter Ring / Trim Ring (black) D6-NCB New Construction Bracket |
| Cutout Diameter | 10.25" (260 mm) |
| Dimensions (Dia x D) | 11.02" (280 mm) x 6.83" (173.4 mm) |
| Net Weight | 11.1 lbs (5 kg) |
| Shipping Weight (Pair) | 31.3 lbs (14.2 kg) |
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.