- Description
Details
The K-Array KR802 is a self-powered amplification system featuring two channels of class D amplification housed in the subwoofer. The rear panel provides input for a balanced line signal, a balanced microphone signal with phantom power and digital signals in AES/EBU protocol also on an XLR for ease of cabling.
The KR802 features two of the KMT218's which are much more than a standard 2 x 18” powered subwoofer. The amplifier mounted on board is class D, delivering 2 x 2400 W at 4Ω. One of the two amplifying channels is dedicated to an output Speakon to connect to many kinds of speaker configurations, including single mid-high modules (KY102, KP52, KP102), multiple line arrays, or the passive version of an additional bass module (KMT218P, KMT18P or KMT21P). The rear panel provides input for a balanced line signal, a balanced microphone signal with phantom power, and digital signals in AES/EBU protocol, also on an XLR for ease of cabling. An integrated touch screen provides intuitive managing and editing of powerful DSP controlling: Input and output levels, In/Out routing, speakon output delay, subwoofer delay, overall system delay (up to 330 ms). All DSP functions, including EQ can be controlled with remote managing software via USB or RS485, again conveniently on a standard XLR. To optimize performance, the onboard DSP includes presets to drive K-array speakers.
The chassis features large ports designed to be fully symmetrical to the speakers, which means the back loading on the drivers is consistent and even with no port air turbulence. This also gives incredible structural strength to the cabinet despite its light weight. Pocket handles and an M20 thread mount position for attaching mid-high speakers makes the KMT218 convenient to use and ideal for medium throw applications in theaters, concert halls, and Audio/Video installations.
- Features
Features
- High power 135 dB continuous, 142 dB peak
- Line array emission wavefront
- DSP onboard with dedicated presets
- Ultra fast setup and dismantling system
- RS485 and USB connectivity for remote control
- Specification
KMT218 Power Handling 1600 W Max power 2800 W Impedance 4 Ω Frequency range (-10 dB) 30 Hz – 150 Hz SPL 1W/1mt 101 dB Maximum SPL 133 dB (cont.) – 139 dB (peak) Crossover Internal DSP controlled Frequency Low pass @ 150 Hz
(maximum - preset dependent)Tranducers 2X 18” Neodymium magnet woofer with 3” voice coil Analog connectors 2 male + 2 female 3-pin balanced XLR Digital connectors 1 male + 1 female 3-pin balanced XLR Connectors s 1 male + 1 female XLR parallel
1 USB B Jack serial converterAmplifier 1 module class D - DSP controlled Subwoofer Power Output 2400 W @ 4 Ω 1% THD + NOISE Speakon Power output 2400 W @ 4 Ω 1% THD + NOISE Protections Over Temp.(Power Limiting – Thermal Shutdown), Short Circuit/Overload Output Protection, Power Limiting, Clip Limiter/Permanent Signal Limiter, High Frequency Protection Frequency Response 20 Hz – 20 kHz (+0 -1 dB) for 1 W @ 8 Ω Nominal Power Requirements 100 - 240 Vac ± 10% 50-60 Hz Operating Range 85 – 265 Vac (auto-range) Power Factor (cosφ) >0.90 @ 4Ω full power 1/8 Rated Power (pink noise) @ 4Ω 600 W Dimensions (H x W x D) 37.4" (949 mm) x 23.6" (600 mm), 18.9" (480 mm) Weight 99.2 lbs (45 kg) KY102 Power handling 1200 W Max power 1800 W Frequency range 90 Hz – 20 kHz (- 3dB) Impedance 8 Ω / 32 Ω (selectable) SPL 1W/1mt 102 dB Maximum SPL 132 dB (cont.) – 138 dB (peak) Crossover External Crossover required Frequency High pass @ 90 Hz, 24 dB/oct suggested minimum Tranducers 8 x 4” Neodymium magnet cone drivers with 1.5” voice coil Connectors 2 x 4-pin Speakon Dimensions (H x W x D) 39.4" (1000.76 mm) x 4.6" (116 mm), 5.3" (134 mm) Weight 32.8 lbs (14.9 kg) - Documents
- In the Box
In the Box
- (1) KMT218 Sub
- (2) KY102 Neodymium Speaker Elements
- (1) K-FOOT2
- (2) K-JOINT2
- Reviews
Write Your Own Review