- Description
Details
Carvin LT5204 5150W 4-Channel PFC Power Amplifier
The LT5204 5150W 4-channel PFC Power Amplifier is a lightweight power amp that provides unlimited flexibility with pure amplification of the original signal source to extreme levels, covering all frequencies without added color. The LT5204 features a single space 1U frame, is 2 ohms capable, and includes PFC Power Factor Correction, which is internationally recognized as the foremost self-regulating power supply for high-end amplifiers. The LT5204 has exceptional headroom with lower power requirements than amps with a traditional power supply. Other models available in the LT Series are the LT2000 2010W 2-channel PFC power amplifier, and the LT5800 2-channel 5760W PFC power amplifier.
The LT5204 4ch model delivers 4x 440W RMS at 8 ohms, 4x 780W at 4 ohms and 4x 1290W at 2 ohms. The LT5204 may be configured into two bridged outputs to deliver 2575W into two bridged 4 ohms loads.
Power Factor Correction
PFC Power Factor Correction corrects the incoming AC power by synchronizing the AC voltage to the line current to reduce energy consumption and heat, which produces substantially more power from the same AC input.
Crystal Clear Transparency
Crystal clear transparency is provided by CLASS D output stages featuring linear circuits with a near theoretical zero distortion level. Fast slew rate 50V/μs circuits produce power at extreme levels, delivering audio in its purest state with no added color.
Single Rack Space Frame Design
Features include the 1U all steel 1.73" H X 19" W frame. The space saving lightweight design doubles amp rack capacities over traditional 2U designs.
PowerCON A/C Connector
The twist-lock design of the PowerCON A/C connector is the professional standard for touring amplifiers.
Advanced Air Flow Design
Cold air is drawn in from the front and expelled out the back, cooling the amp with cold air from the front of the rack.
Channel Inputs
The XLR balanced inputs help reduce signal interference and allow longer cable runs from your signal source (mixer, etc).
Speaker Outputs
Twist-Lock connectors are featured for high power applications. Secure the Twist-Lock cable connection by turning to the right to the lock position. Twist-Lock outputs are compatible with standard 2-conductor Twist-Lock cables. A 4 conductor Twist-Lock cable will enable bi-amping with one 4 conductor cable.
Protect and Limiter Circuits
The PROTECT circuit will engage when the output load draws excessive current or a direct short is detected caused by a shorted speaker cable or speaker system. Thermal protection is also included in the PROTECT circuit. The LIMITER is designed to protect against distortion by automatically reducing the signal to prevent hard clipping, which helps protect the drivers. This feature can be turned off if desired.
70V Distribution System
The LT Series also accommodates for distribution systems. Connect a number of speakers with 70V transformers (in parallel) to the output of the amplifier to drive multiple loudspeakers in a given venue.
Input Sensitivity Adjustments
Input Sensitivity adjustments allow you to decide how much input signal is required to achieve full power output from the amplifier. Choose from four levels of adjustment from +2dBu (.97V) to +12dBu (3V).
- Features
Features
- Active PFC Power Factor Correction
- Space saving lightweight 1-U frames
- High slew rate class D design
- Natural, pure-state amplification
- Up to 5760W, 1010W 8 ohms RMS
- 2 ohm operation, 4 ohm bridged design
- For 70V distribution systems
- Soft-Start 100-240VAC 50-60Hz
- PowerCON™ AC connector
- Front to rear cooling system
- IEC60065 compliant, CB certified
- Up to 12 LT amplifiers in one 12U rack case
- Specification
Channels 4-Channel 8Ω/Stereo 4 x 440W 4Ω/Stereo 4 x 780W 2Ω/Stereo 4 x 1290W 8Ω/Bridge 2 x 1520W 4Ω/Bridge 2 x 2575W 70Vrms (70V Distribution Systems) 2 x 900W Bridge Mode THD (10% Rated Power, Typical) 0.02% Input Impedance 20kΩ Balanced, 10kΩ Unbalanced Damping Factor ≥5000 Signal to Noise Ratio ≥ 99dB AC Input 100-240VAC 50-60Hz Protection Circuits Under Voltage, DC, Thermal, Overload, Short Circuit, Limiter Dimensions (H x W x D) 1.73" (43.94 mm) x 19" (483 mm) x 14.56" (369.82 mm) Net Weight 22.4 lbs (10.16 kg) - Documents
Documents
- Reviews
Write Your Own Review