Peavey IPR2 5000 Power Amplifier

Home /
Shop By Brand /
Peavey /
Peavey IPR2 5000 Power Amplifier

Description

Details

The Peavey IPR2 5000 is designed with a resonant switch-mode power supply and a high-speed class D topology that yields the highest audio resolution and efficiency available. This revolutionary amplifier offers the sonic superiority and unsurpassed reliability for which Peavey is famous, in an extremely efficient and lightweight design.

Advanced technology and extensive protection circuitry allow operation with greater efficiency into difficult loads and power conditions. The DDT (Distortion Detection Technique) circuitry ensures trouble-free operation into loads as low as 2 ohms. DDT protects drivers and ensures that sonic integrity is maintained, even in extreme overload conditions. The IPR2 5000's high-efficiency design allows the amplifier to operate at very low temperatures, and does not require massive heat sinks to cool.

Features

Features

2-channel independent, fourth-order Linkwitz-Riley crossovers.
DDT (Distortion Detection Technique) protection.
Revolutionary IPR class D topology.
Detented input controls.
Combination XLR 1/4" inputs.
4 pole twist lock output connectors.
Ultra-light weight.
Individual signal pass 1/4" jacks on each channel.
LED illuminated.
Standby, LED power present indication.

Specification

Power
Rated Watts (2 x 2 ohms)	3230 W 20 mS repetitive burst / 2530 W 1% THD both channels driven @ 1kHz
Rated Watts (2 x 4 ohms)	1985 W 20mS repetitive burst / 1700 W 1% THD / 1470 W 0.15% THD, both channels driven @ 1kHz
Rated Power (2 x 8 ohms)	1175 W 20mS repetitive burst / 1025 W 1% THD / 880 W 0.15% THD, both channels driven @ 1kHz
Rated Power (1 x 2 ohms)	2,900 W RMS
Rated Power (1 x 4 ohms)	1,780 W RMS
Rated Power (1 x 8 ohms)	975 W RMS
Minimum Load Impedance	2 ohms
Maximum RMS Voltage Swing	105 volts
Frequency
Frequency Response	20Hz - 22kHz; +/- 0.5 dB at 1 W
20Hz - 20kHz (2 x 2 ohms)	<0.5% @ 2250 W 20Hz to 4kHz, decreasing to 1640 W @ 20kHz, both channels driven
20Hz - 20kHz (2 x 4 ohms)	<0.15% @ 1400 W 20Hz to 10kHz, decreasing to 1350 W @ 20kHz, both channels driven
20Hz - 20kHz (2 x 8 ohms)	<0.15% @ 860 W 20Hz to 4kHz, increasing to 1000 W @ 20kHz, both channels driven
Input CMRR	> - 75dB @ 1 kHz
Voltage Gain	x 40 (+32dB)
Crossover	100 Hz switchable 2nd order High pass and 3rd order Low Pass per channel
Crosstalk	> -60dB @ 1kHz @ 700 W power @ 8 ohms
Hum and Noise	> -105dB, “A” weighted referenced to rated power @ 4 ohms
Slew Rate	> 12V/μs
Damping Factor (8 ohms)	> 210:1 @ 20 Hz - 1 kHz at 8 ohms
Input Sensitivity	1.95 volts +/- 3% for 1kHz 4 ohm rated power, 1.83 volts +/- 3% for 1kHz 2 ohm rated power
Input Impedance	20k ohms balanced and 10k ohms unbalanced
Current Draw
Current Draw @ 1/8 in VA (watts)	1435 (890) @ 2 ohms, 920 (525) @ 4 ohms, 625 (335) @ 8 ohms
Current Draw @ 1/3 in VA (watts)	3050 (2155) @ 2 ohms, 1880 (1200) @ 4 ohms, 1200 (715) @ 8 ohms
Idle Consumption	195VA, 90 W
Cooling	3 temperature dependent variable speed fans
Controls	2 front panel attenuators, crossover select switch for HPF, Normal and LPF
Indicator LEDs	Five LED indicators per channel: Active, Signal, DDT, Temperature and DCand 2 DC protect
Protection	Thermal, DC, subsonic, incorrect loads, under and over voltage
Connectors	Inputs: Dual combo 1/4” XLR, Outputs: Dual 1/4” thru, one 2-pin & one 4 pin twist-lock connector
Construction	0.062” thick aluminum
General
Dimensions	3.5" H x 19.0" W x 17.0" D behind front panel + 0.6” for handle (89 mm x 483 mm x 432 mm)
Shipping Dimensions	21.2" H x 21.0" W x 6.0" D (538 mm x 533 mm x 152 mm)
Weight	13.67 lbs (6.2 kg)
Shipping Weight	17.42 lbs (7.9 kg)

Documents