- Description
Details
The MXWANI4 enables easy out-of-the-box system setup with no additional networking hardware required. With per-channel analog outputs, it is the central point for connecting and distributing Microflex Wireless systems and the Microflex Advance MXA310 Table Array to conference room AV networks.
- Works with Microflex Wireless and Microflex Advance devices equipped with Dante digital networked audio
- Offers 4 block connector channel outputs, 1 block connector input, and a headphone output
- Features power over Ethernet and networked control via Microflex Wireless Control Software
- Includes MXWANI4, IEC cable, hardware kit, and user guide
- Features
Features
- Four-port gigabit switch: Optimized port configurations for connection to the access point transceiver and networked charging stations, third-party control systems, and corporate networks
- Ethernet connectivity: Send audio and control signals over long cable runs of up to 300 feet or anywhere over a corporate network
- Power over Ethernet: Port 1 of the rear panel switch supplies power over Ethernet to the access point transceiver (APT) or MXA310 for simplified installation
- Corporate uplink mode: Link to the corporate network for remote control of system settings while keeping audio off the network for security and to reduce bandwidth
- Front panel controls: Mute or solo channels and set input/output levels easily from the front panel
- PC / Mac software control: Access the Microflex Wireless Control Software from a networked computer for input/output levels and port configuration
- Dante™ networking: Transports low-latency digital audio received from wireless microphones over Ethernet to any other Dante-equipped device
- Headphone output: Solo audio signal on any channel
- Specification
Audio Frequency Response 20 Hz to 20 kHz (+1, −1.5 dB) Dynamic Range (20 Hz to 20 kHz, A-weighted, typical)
Analog-to-Dante: 113 dB
Dante-to-Analog: 110 dBOutput Noise (20 Hz to 20 kHz, A-Weighted, typical)
Line: −84.5 dBV
Aux: −95.2 dBV
Mic: −106.5 dBVTHD+N <0.05% (20 Hz to 20 kHz @ +4dBu analog input,-10 dBFS digital input) Polarity Non-inverting, any input to any output Housing Steel; Extruded aluminum Power Requirements 100 to 240 V AC, 50-60 Hz, 1 A Operating Temperature Range −18°C (0°F) to 63°C (145°F) Analog Connections - Outputs Configuration Active Balanced Impedance 310 Ω Clipping Level (Minimum) Line: +26.2 dBV
Aux: +16.2 dBV
Mic: −3.8 dBVAnalog Connections - Input(s) Configuration Active Balanced Impedance 10.6 kΩ Clipping Level (Minimum) Line: +23.8 dBV
Aux: +10.8 dBVHeadphone Output 6.35 mm (1/4”) TRS, 100 mW, 350 Ω, dual mono (will drive stereo phones) AD/DA Converter 24-bit, 48 kHz Latency (Estimated Nominal, ±0.1 ms) Analog-to-Dante: 0.21 ms
Dante-to-Analog: 0.24 ms + TNNetworking Network Interface Four-Port Gigabit Ethernet Switch, Dante digital audio Uplink Port (Port 4) Selectable, blocks multicast traffic Power over Ethernet (PoE) Provided on Port 1 to power MXWAPT Cable Requirements Cat 5e or higher, shielded, 100 m maximum between network devices Network Addressing Capability DHCP, link-local, static Dimensions (H x W x D) 1.7" (44 mm) x 19.0" (483 mm) x 14.4" (366 mm) Weight 6.9 lbs (3.1 kg) - Documents
Documents
- Reviews
Write Your Own Review