Community C4LP 4.5 inch 2 Way Ceiling Speaker - Pair (Discontinued)

By Community

Community C4LP 4.5 inch 2 Way Ceiling Speaker - Pair (Discontinued)

Write a Review

Part #:

C4LP

Model #:

C4LP

Current Stock:

Availability: No Longer Available

Contact us for comparable solutions.

Certified Audio
Expertise

FREE Custom
System Design

Get Expert
Help Fast

Ask an Expert

Our expertly trained Sales Engineers are ready to help!

(888) 256-4112

The Community C4LP Commercial Design Ceiling Speaker provides high quality paging & musical performance. Uniform voicing means that it can be combined with the larger models of the Commercial Design Series without compromising consistency.

Description

C4LP is the C4 coaxial design in a low profile back can for use when clearances above the ceiling are minimal. The C4 has a wider dispersion than the larger models. The C4 contains a proprietary Tru-Phase™ waveguide that produces a consistently wide conical polar response up to 16 kHz. It features a genuine coaxial design using separate magnets for the LF and HF drivers for reduced distortion and high sensitivity, thereby permitting up to 3 dB greater output level while requiring up to half the amplification power of competing products. The C SERIES ceiling loudspeakers are all ETL listed, and have similar sensitivity and output capabilities.

Features

High intelligibility with exceptional uniform coverage
Consistent, wide dispersion up to 16 kHz
True coaxial loudspeakers with HF compression drivers
Tru-Phase™ high-frequency waveguide
Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails simplify installation
Uniquely designed tile bridge support rails prevent ceiling tile sagging
External loop-through Euroblock connectors
Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
Face-mounted adjustable tap position selector switch
Selectable 8 ohm or 70V/100V operation

Specifications

Operating Range	90 Hz - 13.5 kHz (-10 dB)
Frequency Response	160 Hz - 12.5 kHz (-3 dB)
Max Input Ratings (8 ohm)	60W continuous, 150W program 21.9 volts RMS, 43.8 volts momentary peak
Transformer Taps	70V: 8W, 4W, 2W, 1W, and 8 ohm selectable 100V: 16W, 8W, 4W, 2W, and 8 ohm selectable
500 Hz	2nd Harmonic : 0.53%, 3rd Harmonic : 0.35%
2 kHz	2nd Harmonic : 0.64%, 3rd Harmonic : 0.32%
8 kHz	2nd Harmonic : 3.22%, 3rd Harmonic : 0.09%
500 Hz	2nd Harmonic : 0.19%, 3rd Harmonic : 0.35%
2 kHz	2nd Harmonic : 0.90%, 3rd Harmonic : 0.14%
8 kHz	2nd Harmonic : 0.82%, 3rd Harmonic : 0.03%
Sensitivity (1W/1m)	91 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands), 92 dB SPL (250 Hz to 4 kHz speech range)
Maximum Output	8Ω: 109 dB SPL / 115 dB SPL (peak) 70V: 100 dB SPL / 106 dB SPL (peak) 100V: 103 dB SPL / 109 dB SPL (peak)
Nominal Impedance	8 ohms
Minimum Impedance	6.5 ohms @ 10 kHz
Nominal Coverage	130º conical (1 kHz to 6 kHz ±70°), 140° conical (500 Hz to 6 kHz ±70°)
Axial Q / DI	3.9 / 5.9
Crossover Frequency	2 kHz
Recommended Signal Processing	140 Hz, at 24 dB per octave high pass filter
Drivers	LF 1 x 4.5" cone, HF 1 x 3/4" exit compression driver
Driver Protection	Self-resetting solid state circuit breaker
Input Connection	4-pole Euroblock connector with two pair of non-interrupt parallel connections
Controls	Front-face wattage / low impedance selector switch
Enclosure	Corrosion-resistant zinc plated steel
Finish	White
Mounting/Rigging Provisions	2 ABS mounting clamps with 1.75" grip range
Grille	Powder coated steel with safety line, white finish, paintable
Baffle	Reflex loaded UL 94V-0 rated ABS
Safety Features	2 x safety hang points
Required Accessories	Electronic high pass filter
Supplied Accessories	Tile support bridge rails, grille, paint mask, cut-outtemplate, flat screwdriver
Cutout Diameter	7.36" (187 mm)
Dimensions (Dia x D)	8.31" (211 mm) x 3.61" (91.7 mm)
Net Weight	5.9 lbs (2.7 kg)
Shipping Weight (Pair)	15 lbs (6.8 kg)