Community D5 5 inch 2-Way Ceiling Speakers

Home /
Commercial Sound Equipment /
Commercial Audio Speakers /
In-Ceiling & In-Wall Speakers /
70 Volt In Ceiling Speakers /
Community D5 5" 2-Way Ceiling Speakers - Pair

Description

Details

Community D5 5" 2-Way Ceiling Speakers

The D5 has a more focused dispersion, higher sensitivity and output than the smaller D4. The high performance D5 is a true coaxial loudspeaker with a real compression driver concentrically arranged so that the upper frequencies emerge through the center of the low-frequency driver’s magnetic structure and cone via a precisely tapered Tru-Phase™ high-frequency waveguide. This special construction provides consistent, wide dispersion up to 16 kHz, all but eliminating high-frequency narrowing. Further pattern improvement is achieved by precisely mounting the low frequency driver (and its concentric HF driver) centered in the baffle, as contrasted to the offset designs used by others.

The D SERIES offers powerful magnetic structures and efficient coils to ensure high output, which results in more headroom per power amplifier. Each D SERIES ceiling model is available as a complete assembly, including everything needed for standard installations, and can also be ordered as separate faces and back cans. The model has a built-in autoformer allowing it to be used in 8-ohm or 70V/100V applications. The D SERIES ceiling loudspeakers are ETL listed and all models have been tested by ETL to comply with UL1480, UL2043 and CSA60065.

Features

Features

High intelligibility with exceptional uniform coverage
Consistent, wide dispersion up to 16 kHz
True coaxial loudspeakers with HF compression drivers
Tru-Phase™ high-frequency waveguide
Patented Carbon Ring Cone Technology™
Spring loaded Drop-Stop™ installation assistant tabs support the back can on the included rails and C-ring to simplify installation
Uniquely designed tile bridge support rails and snap-on C-ring support plates prevent sag
Twist-Assist™ loudspeaker face retainer tabs for fast and easy installation
3/4" and 1" knock-outs on the sides of the back can
External loop-through Euroblock connectors
Rear cover with integrated cable clamp (strain relief) and optional conduit knockout
Selectable 8 ohm or 70V/100V operation
Back can and face-only packages available
Five year warranty

Specification

Operating Range	65 Hz - 22 kHz
Frequency Response	80 Hz - 20 kHz (±5 dB)
Max Input Ratings (8 ohm)	100W continuous, 250W program 28 volts RMS, 63 volts momentary peak
Sensitivity (1W/1m)	93 dB SPL (125 Hz to 12.5 kHz 1/3 octave bands) 91 dB SPL (250 Hz to 4 kHz speech range)
Maximum Output	113 dB SPL / 119 dB SPL (peak 8 ohm)
Nominal Impedance	8 ohms
Axial Q / DI	4.5 / 6.5, 500 Hz to 6 kHz
Crossover Frequency	1.6 kHz
Drivers	LF 1 x 5" HF 1 x 1" exit compression driver
Driver Protection	Self-resetting solid state circuit breaker
Input Connection	4-position Euroblock connector
Controls	Front-face wattage / low impedance selector switch
Enclosure	Corrosion-resistant zinc plated steel
Mounting/Rigging Provisions	4 steel mounting clamps with 3-inch grip range
Grille	Powder coated steel with safety line, white finish, paintable
Baffle	Reflex loaded UL 94V-0 rated ABS
Safety Features	4 x safety hang points
Safety Agency Ratings	ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling spaces per NFPA 70 and NFPA 90
Required Accessories	Electronic high pass filter
Supplied Accessories	C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template, flat screwdriver
Optional Accessories	D45-FAR Face Adapter Ring D45-CATR Can Adapter Ring / Trim Ring D45-NCB New Construction Bracket
Cutout Diameter	8.75" (222 mm)
Dimensions (Dia x D)	9.53" (242 mm) x 6.83" (173.4 mm)
Net Weight	10.4 lbs (4.7 kg)
Shipping Weight (Pair)	29.6 lbs (13.4 kg)

Documents