Community D8 8" 2-Way In-Ceiling Loudspeaker - Pair (Discontinued)
Usually arrives in 5-9 business days.
The Community D10 exceeds the performance of competing "high-ceiling" models and provides high-level foreground music, loud-and-clear paging and readily supports large systems in sports facilities, clubs, or concert venues for delay and zone fill.
The flagship model of the D SERIES, the D10 exceeds the performance of competing “high-ceiling” models. The D10 provides high-level foreground music, loud-and-clear paging (even in noisy environments), and readily supports large systems in sports facilities, clubs, or concert venues for delay and zone fill. Characterized by powerful, musical performance and superb speech intelligibility, the D10 represents a significant change in the ceiling speaker market segment.
D10’s can readily be combined with smaller members of the Distributed Design family due to Community’s uniform voicing technology, providing additional power and LF response in areas that require it. True coaxial design uses separate magnets for the LF and HF drivers for reduced distortion and industry-leading sensitivity permitting 3 dB to 6 dB greater output level, while requiring half the amplification power of competing products.
The proprietary Tru-Phase™ waveguide and perfectly centered driver produce a consistently wide conical polar response up to 16 kHz. Community’s patented Carbon Ring Cone Technology™ increases the effective cone area to further reduce distortion while reinforcing the cone for improved durability.
Exclusive Drop-Stop™ and Twist-Assist™ tabs allow single-handed placement to speed installation and reduce labor time. Drop-Stop’s spring-loaded legs support the back can on the included tile rails and snap-on C-ring, so that the installer no longer needs to hold the can against the tile while tightening the clamps. Twist-Assist performs a similar function for the baffle assembly: when the loudspeaker back cans are pre-installed into a conduit system for termination at a later date, a simple twist of the baffle into the back can brings the Twist-Assist clips together, supporting the baffle assembly while the installer fastens the screws.
The front-face wattage selector switch enables quick adjustment of levels, while the high-power internal autoformer permits full power output with 70V or 100V lines. A variety of installation accessories are available to accommodate different ceiling materials. The D10 face-only assembly and back can are also available for separate purchase.
| Operating Range | 58 Hz - 22 kHz |
|---|---|
| Frequency Response | 75 Hz - 20 kHz (±5 dB) |
| Max Input Ratings (8 ohm) | 200W continuous, 500W program; 40 volts RMS, 89 volts momentary peak |
| Transformer Taps - 70V | 200W, 100W, 50W, 25W and low impedance |
| Transformer Taps - 100V | 200W, 100W, 50W |
| 500 Hz | 2nd Harmonic 0.92%; 3rd Harmonic 0.88% |
| 2 kHz | 2nd Harmonic 0.81%; 3rd Harmonic 0.30% |
| 8 kHz | 2nd Harmonic 2.9%; 3rd Harmonic 0.04% |
| 500 Hz | 2nd Harmonic 0.17%; 3rd Harmonic 0.71% |
| 2 kHz | 2nd Harmonic 0.07%; 3rd Harmonic 0.16% |
| 8 kHz | 2nd Harmonic 1.04%; 3rd Harmonic 0.01% |
| Sensitivity (1W/1m) | 98 dB SPL (100 Hz to 12.5 kHz 1/3 octave bands); 121 dB SPL (250 Hz to 4 kHz speech range) |
| Maximum Output | 121 dB SPL / 127 dB SPL (peak 8 ohm) |
| Nominal Impedance | 8 ohms |
| Minimum Impedance | 6.6 ohms @ 190 Hz |
| Nominal Coverage | 88º conical (1 Hz to 6 kHz); 100º conical (500 Hz to 6 kHz) |
| Axial Q / DI | 6.5 / 8.1, 500 Hz to 6 kHz |
| Crossover Frequency | 1 kHz |
| Recommended Signal Processing | 58 Hz high pass filter |
| Drivers | LF 1 x 10" HF 1 x 1.25" exit compression driver |
| Driver Protection | Self-resetting solid state circuit breaker |
| Input Connection | 4-position Phoenix connector |
| Controls | Front-face wattage / low impedance selector switch |
| Enclosure | Corrosion-resistant zinc plated steel |
| Mounting/Rigging Provisions | 4 steel mounting clamps with 3-inch grip range |
| Grille | Powder coated steel with safety line, white finish, paintable |
| Baffle | Reflex loaded UL 94V-0 rated ABS |
| Safety Features | 4 x safety hang points |
| Safety Agency Ratings | ETL listed to comply with UL1480, UL2043 and CSA60065. Suitable for use in air handling |
| Face-Only / Back Can Options | D10-FO Face-Only Assembly D10-BC Back Can |
| Required Accessories | Electronic high pass filter |
| Supplied Accessories | C-Ring supporting plate, tile support bridge rails, grille, paint mask, cut-out template |
| Optional Accessories | D10-NCB New Construction Bracket |
| Cutout Diameter | 14.125" (359 mm) |
| Dimensions (Dia x D) | 14.96" (380 mm) x 9.98" (253.4 mm) |
| Net Weight | 23.1 lbs (10.5 kg) |
| Shipping Weight (Pair) | 60 lbs (27.2 kg) |
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.
Model #:
Usually arrives in 5-9 business days.